Easy to Install RCO810 3 n' 1 Start Hard Start Kit Supco Starter - Replaces TJ90RCO810 ERP810 HS8 HS810 RC0810 RC100 RCO810

Easy to Install RCO810 3 n' 1 Start Hard Start Kit Supco Starter - Replaces TJ90RCO810 ERP810 HS8 HS810 RC0810 RC100 RCO810

Use the 3-in-1 relay combo kit with capillary refrigeration systems. Compatible compressor sizes range from 1/12 to 1/5 HP. You can install the kit in just a few minutes. No tools are required. Doing so will boost start-up to prevent low voltage starting problems. This high-quality exact replacement part meets or exceeds all original manufacturer specifications for compatibility and performance. Specs - Voltage: 115, Horsepower: 1/12 to 1/5.

Installation Instruction

1. Disengage the power supply.

2. Eliminate old relay and overload.

3. Push the terminal connected with the white wire on RCO onto the beginning terminal of the blower.

4. Push the terminal connected with the red wire on RCO onto the run terminal of the blower.

5. Push the terminal associated with the black wire on RCO onto the common terminal of the blower.

6. Link one line wire which was eliminated from the old relay to one of the line wires of the RCO with a wire nut.

7. Connect the other line wire which was eliminated from the old overload to the next line wire of the RCO, with a wire nut.

Features of Easy to Install RCO810 3 n' 1 Start Hard Start Kit Supco Starter - Replaces TJ90RCO810 ERP810 HS8 HS810 RC0810 RC100 RCO810

?? Rco810 3 N' 1 Start Hard Start Kit - A high-quality exact equivalent for part numbers TJ90RCO810, AP4503019, ERP810, HS8, HS810, RC100. Supco Rco810 3 N' 1 Start Hard Start Kit is compatible with compressor sizes range from 1/12 to 1/5 HP. The Supco Rco810 Start Kit is a type of hard start capacitor that is designed for refrigeration systems. Includes relay, capacitor, and overload device, pre-wired. HVAC Starter Kit fits hundreds of models and can be installed in a few minutes. | ?? DIY eTips Included - Not sure how to replace the part? Helpful information can be found on the page below. Scroll down to get more repair tips. Acquire valuable skills during the DIY repair project. Supco Rco810 3-in-1 Hard Start Kit For Freezers will help if your appliance compressor doesn't start. Kit replaces all 3 electrical components on capillary refrigeration systems. Installing the RCO810 kit is a straightforward process that does not require any special tools or skills. | ?? The Supco Rco810 3-in-1 Hard Start Kit For Refrigerators can be used with refrigerators, freezers, and ice machines. It is compatible with refrigeration systems that have compressors with a horsepower rating between 1/12 and 1/5. It provides an all-in-one solution that simplifies installation and eliminates the need for multiple parts. Rco810 AC Capacitor Kit meets or exceeds all manufacturer specifications. We provide a lifetime warranty and guarantee 100% money back. | ?? How do you test a hard start capacitor? To test a hard start capacitor in a fridge, you should first disconnect the power source and locate the cylindrical-shaped capacitor near the compressor with two or three electrical terminals. Use an insulated screwdriver to discharge any residual charge before using a multimeter in capacitance mode to test the capacitance and resistance mode to test the resistance between the terminals. The readings should be within the range specified by the manual. | ?? Can a fridge run without a capacitor? No, a fridge cannot run without a capacitor. The capacitor is a crucial component of the fridge's compressor motor, responsible for providing the initial jolt of electricity to start the motor. Without a capacitor, the motor may struggle to start or fail to start altogether. In some cases, attempting to run a fridge without a capacitor can even damage the compressor motor or other components of the fridge's electrical system.